FA-X / FA-M Error handling

DataDictionary				Number (new)	Error number old	Text Display	Possible cause	Solution
130	0x0082	Bit 0	Internal error: data corruption	Error 001	E01	Internal error: data corruption	Supply voltage was disconnected too quickly after a parameter change; save process was not fully completed.	Clear the error by restoring the factory setting with the [rE5] function or parameter. Use engineering tool to import a valid dataset. If the error [E01] occurs again after you reactivate the supply voltages, contact Schmalz Service.
130	0x0082	Bit 2	Supply voltage too low	Error 003	E07	Primary voltage too low	Sensor supply voltage is too low.	Check power supply unit and power load. Increase supply voltage
130	0x0082	Bit 3	Supply voltage too high	Error 004	E17	Primary voltage too high	Sensor supply voltage is too high.	Check power supply unit. Reduce supply voltage
130	0x0082	Bit 6	Short circuit at OUT2	Error 007		Short circuit at OUT2	Short circuit at OUT2.	Check OUT2.
130	0x0082	Bit 10	Vacuum Sensor calibration failed	Error 011	E03	Vacuum sensor calibration failed	Zero-point adjustment for vacuum sensor is outside of the tolerance 3% FS. Calibration was canceled when measurement value was too high or too low.	Vent the vacuum circuit. Calibrate the vacuum sensor again.
130	0x0082	Bit 11	Pressure Sensor calibration failed	Error 012		Pressure sensor calibration failed	Zero-point adjustment for pressure sensor is outside of the tolerance 3% FS. Calibration was canceled when measurement value was too high or too low.	Vent the vacuum circuit. Calibrate the pressure sensor again.
130	0x0082	Bit 15	IO-Link communication interruption	Error 016	E08	IO-Link communication abruption	Connection to the master interrupted.	Check connection line. Repeat the power-up process.
146	0x0092	Bit 0	Valve protection	Warning 001		Valve protection active		Check the system for leakage. If necessary, adjust “Min. evacuation time” using the process settings.
146	0x0092	Bit 1	Evacuation time above limit	Warning 002		Evacuation time above limit		Check the system for leakage. If necessary, adjust “Permissible evacuation time t1” using the process settings.
146	0x0092	Bit 2	Leakage rate above limitd	Warning 003		Leakage above limit	The set leakage rate was exceeded.	Check the system for leakage. If necessary, adjust “Permissible leakage rate” using the process settings.
146	0x0092	Bit 3	SP1 not reached in suction cycle	Warning 004		SP1 not reached in suction cycle	The set switching point was not reached in the last cycle.	Check the system for leakage. If necessary, adjust “SP1” using the process settings.
146	0x0092	Bit 4	Free Flow Vacuum over SP2	Warning 005		Free flow vacuum over SP2	During unobstructed suction, the vacuum value is above the parts detection level (SP2).	Check the system for contamination and ensure that the cross sections are appropriate. If necessary, adjust SP2 using the process settings.
146	0x0092	Bit 5	Sypply voltage out of operating range	Warning 006		Primary voltage out of operating range	Supply voltage: outside permissible range.	Check the supply voltage.
146	0x0092	Bit 8	Input pressure out of operation range	Warning 009		Input pressure out of operating range	The input pressure is outside the specified range.	Check the input pressure.
146	0x0092	Bit 12	Air saving function limited	Warning 013		Air saving function limited, less vacuum detected	The air-saving function detects a low vacuum and limits the minimum number of ejectors that can be deactivated.	Check the system for leakage. If necessary, adjust “SP1,” “SP2” or “Min. evacuation time” using the process settings.